Description Free Sample High Quality Good Adhesion Potting and Sealing Electronic Components RTV2 Liquid Silicone Rubber Factory
HY-9025 is a kind of low viscosity, Inherent flame resistance, two components addtion cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time.
Application Free Sample High Quality Good Adhesion Potting and Sealing Electronic Components RTV2 Liquid Silicone Rubber Factory
HY-9025 is suitable for bonded seal of electronic components, power module and control module, LED invertor potting, etc which requires waterproof and insulation. It can be broadly used for LED screen, Wind Power Generator, PCB, substrate, etc.
Technical Parameters
(Pls note: the above data for this product in 25 ºC temperature, 55 percent humidity conditions, for reference. The accurate data is measured by customers when using.)
TECHNICAL GUIDELINES
1, Typical Application
HY-9025 could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. Pls put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 1:1
3, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4, Pls note that the thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100ºC, the silicone will cure in 15 minutes; while in 25ºC room temperature, the silicone will cure around 8 hours.
Notes:
1.The following material may hinder the curing of GD-8055, so pls use after the test. When necessary, pls clean the application areas.
Organotin compound or Condensation silicone with organotin
Sulphur, sulfide and sulfur rubber materials.
Amine compounds as well as contains the amine materials.
Pewters solder flux
2. HY-9025 should be sealed storage.The mixture should be used up disposably to avoid causing waste.
3. HY-9025 belongs to non-dangerous goods, but keep away from mouth and eyes.
4. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance.
PACKAGE: Free Sample High Quality Good Adhesion Potting and Sealing Electronic Components RTV2 Liquid Silicone Rubber Factory
20Kg/pail as a set (Part A 10Kg + Part B 10Kg)
SHELF LIFE AND TRANSPORTATION
3. Storage beyond the expired date does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
HY-9025 is a kind of low viscosity, Inherent flame resistance, two components addtion cured potting silicone with heat-conducting. It cures with both on room temperature and heated temperature. It has the feature of the higher temperature the faster of the curing time.
Application Free Sample High Quality Good Adhesion Potting and Sealing Electronic Components RTV2 Liquid Silicone Rubber Factory
HY-9025 is suitable for bonded seal of electronic components, power module and control module, LED invertor potting, etc which requires waterproof and insulation. It can be broadly used for LED screen, Wind Power Generator, PCB, substrate, etc.
Technical Parameters
| Model | Color | Viscosity (cps) | Hardness (A°) | Mixing ratio | Operating Time(min) | Curing Time(hr, 25ºC) |
| HY-9025 | Grag | 500±500 | 25±5 | 1:1 | 30~60 | 4~5 |
(Pls note: the above data for this product in 25 ºC temperature, 55 percent humidity conditions, for reference. The accurate data is measured by customers when using.)
TECHNICAL GUIDELINES
1, Typical Application
HY-9025 could be applied to
- high powered electronics,
- DC/DC module and circuit board which requires heat dissipation and high temperature resistance.
-It can be broadly used for LED screen, Wind Power Generator, PCB substrate, etc. Pls put part A and part B in separate container and stir evenly before mixing the two part together.
2, Mixing Ratio: part A: part B = 1:1
3, Deaeration the mixture in vacuum pump under 0.08 MPa for 3-5 minutes.Then the mixture could be used for pouring.
4, Pls note that the thickness of the silicone affects the curing time. If the silicone used is a little thick,then the curing time will be a little longer.The temperature also affects the curing time.When in lower temperature, we suggest customers appropriately heat the mixture to accelerate vulcanization. With temperature of 80~100ºC, the silicone will cure in 15 minutes; while in 25ºC room temperature, the silicone will cure around 8 hours.
Notes:
1.The following material may hinder the curing of GD-8055, so pls use after the test. When necessary, pls clean the application areas.
Organotin compound or Condensation silicone with organotin
Sulphur, sulfide and sulfur rubber materials.
Amine compounds as well as contains the amine materials.
Pewters solder flux
2. HY-9025 should be sealed storage.The mixture should be used up disposably to avoid causing waste.
3. HY-9025 belongs to non-dangerous goods, but keep away from mouth and eyes.
4. When it gets stratified after a period of storage, Please mix it evenly before using,which does not affect the performance.
PACKAGE: Free Sample High Quality Good Adhesion Potting and Sealing Electronic Components RTV2 Liquid Silicone Rubber Factory
20Kg/pail as a set (Part A 10Kg + Part B 10Kg)
SHELF LIFE AND TRANSPORTATION
- Twelve(12) months when stored at 25C in tightly closed original packages.
- This kind of product is non-dangerous product, which could be transported as general chemicals.
3. Storage beyond the expired date does not necessarily mean that the product is no longer usable. In this case however, the properties required for the intended use must be checked for quality assurance reasons.
- Why choose us
1, Long history and solid foundation
With 21 years of development history and good reputation, our products are exported to 138 countries around the world and exported since 2006. 
2, High-end research and development
Being a leading liquid silicone manufacturer(6000 square meter factory )
in China, we have a professional R&D team and QC team(12 experts ) and our product is FDA, SGS, RoHS, MSDS, ISO, REACH, UL approved, so there is no need to worry about the quality.And we have 14 years on alibaba.com, 12 years on made-in-china.com, a trustworthy company
3, Efficient service
We can provide free training of silicone technique and free silicone samples. we have a professional sales team who will solve your problems patiently. Besides, with efficient logistics distribution system, you could get you goods earlier. Last, good after-sales service,we build long term cooperation relationship, once there is quality problem, we could solve right away. More importantly, return and exchange are accepted while quality problems occurred
Please do not hesitate in contacting me should you require any further assistance. I will be happy to help. Free sample
Mobile/ Whatsapp/: +86 189 3886 7508